Hi, thanks for mapping and welcome to HOT.

The buildings you mapped are quite well done as to their location. But pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Also try to avoid mapping several buildings as one building. Every building must be traced separately.

Please watch this short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/129042552

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

The buildings you mapped are well done as to their location. But pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Please watch these 2 short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o
-Roads--> https://www.youtube.com/watch?v=ZBLwb2nisJQ

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/128945199

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

The buildings are unfortunately not correctly traced. This is due to you the fact that you are using the wrong imagery. Please check that you have the Custom Background loaded in your editor (and not Maxar).

Also pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Please watch these 2 short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o
-Roads--> https://www.youtube.com/watch?v=ZBLwb2nisJQ

Thanks so much for your contribution, Martien, HOT validator.

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

The buildings you mapped seem to be on the wrong place. Please double check if you are using the correct imagery. And pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Please watch these 2 short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o
-Roads--> https://www.youtube.com/watch?v=ZBLwb2nisJQ

Thanks so much for your contribution, Martien, HOT validator.
---

Published using OSMCha: https://osmcha.org/changesets/128944994

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

The buildings you mapped here include also the surrounding area. Also please pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Please watch these 2 short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o
-Roads--> https://www.youtube.com/watch?v=ZBLwb2nisJQ

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/128945253

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

The buildings you mapped are well done as to their location. But pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Please watch these 2 short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o
-Roads--> https://www.youtube.com/watch?v=ZBLwb2nisJQ

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/128945288

Hi, thanks for mapping. You requested a review of your mappings.

Your buildings are well mapped. Good location, square corners and precise outline.

Thanks and regards, Martien, HOT validator.
---
#REVIEWED_GOOD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/128945292

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

The buildings you mapped are well done as to their location. But pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Please watch this short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_GOOD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/128132633

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

The buildings you mapped are well done as to their location. But pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Please watch this short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/127842683

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

The buildings you mapped are well done as to their location. But pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Please watch this short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/128009407

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

The buildings you mapped are well done as to their location. But pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Please watch this short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/128085414

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

Most of the buildings you mapped are well done. The tracing is well done and they are on the right spot.

There are unfortunately issues with a few buildings:
* they share nodes with each other or with a road. And they shouldn't. Eg road data is used in sat navs by humanitarian workers. A sat nav will think there is a dead end if it enters a building. This could add hours to a journey.
* also avoid mapping several buildings that are close to each other as one building. Every building must be traced separately.

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/127912435

Hi, thanks for mapping. You requested a review of your mappings.

Your buildings are well mapped. Good location, square corners and precise outline.

Thanks and regards, Martien, HOT validator.
---
#REVIEWED_GOOD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/127193564

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

A few things to consider:
* the buildings you mapped are well done as to their location. But pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

* tag all buildings as building=yes instead of building=house

* while tracing buildings please be careful not to include the courtyard. Zoom in as close as possible to see the outline of the buildings, hit each corner of the building carefully. Look for shadows, open ground, changes in roof color and vegetation to differentiate buildings.

Please watch these 2 short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o
-Roads--> https://www.youtube.com/watch?v=ZBLwb2nisJQ

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/127251661

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

The buildings you mapped are well done as to their location. But pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Another thing to watch out for: avoid buildings sharing nodes or else overlapping with other buildings or with eg roads. Use the Alt key to prevent snapping one feature to the other.

Please watch these 2 short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o
-Roads--> https://www.youtube.com/watch?v=ZBLwb2nisJQ

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/127360257

Hi, thanks for mapping and welcome to HOT. You requested a review of your mappings.

For the most part the buildings are well mapped.

Only point of attention is the building corners need to be squared. After tagging them by pressing ‘q’ on your keyboard.

Also avoid buildings sharing nodes or else overlapping. If buildings need to be adjusted or improved later on, it is much harder to do that if they share nodes with nearby features.

Please watch these 2 short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o
-Roads--> https://www.youtube.com/watch?v=ZBLwb2nisJQ

Thanks so much for your contribution, Martien, HOT validator.
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/126921334

Hi Robert, i am reviewing and validating in this project. Thanks for mapping.

There are unfortunately a few issues here:
* Please avoid mapping several buildings as one building. Every building must be traced separately. Zoom in as close as possible to see the outline of the buildings, hit each corner of the building carefully. Look for shadows, open ground, changes in roof color and vegetation to differentiate buildings.
* Always square your buildings after tagging them by pressing ‘q’ on your keyboard. Except of course when the building has another shape
* Avoid buildings sharing nodes or else overlapping

Kind regards,

Martien, HOT Global Validator
---
#REVIEWED_BAD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/127028087

Hi, thanks for mapping. You requested a review of your mappings.

Well mapped. Good location, square building corners and precise outline.

Small point of attention: you mapped building=house in a few cases. As remote mappers we cannot know the functionality of buildings. So it is common practice to always use building=yes.

Thanks and regards, Martien, HOT validator.
---
#REVIEWED_GOOD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/127059163

Hi, thanks for mapping. You requested a review of your mappings.

Your buildings are well mapped. Good location, square corners and precise outline.

Only issue is that in a few occasions you mapped a building over an existing building. If that happens your editor can suggest to add a layer tag. In most cases this is wrong. Instead you should move one of the 2 features (building or whatever) out of the way.

Thanks and regards, Martien, HOT validator.
---
#REVIEWED_GOOD #OSMCHA
Published using OSMCha: https://osmcha.org/changesets/126576943

Hi Richard, thanks for mapping and welcome to HOT. I am a validator reviewing this project.

The buildings you mapped are well done as to their location. But pay attention to the squareness of the corners. Always draw buildings as square and precise as you can. Then add the Building feature type. And last, right click it and click the square icon.

Also several buildings share nodes with each other. Please avoid doing that. If buildings need to be adjusted or improved later on, it is much harder to do that if they share nodes with nearby features.

Also avoid mapping several buildings as one building. Every building must be traced separately. Zoom in as close as possible to see the outline of the buildings, hit each corner of the building carefully. Look for shadows, open ground, changes in roof color and vegetation to differentiate buildings.

Please watch this short video for more info:
-Buildings--> https://www.youtube.com/watch?v=Xs5wX592E1o

Thanks so much for your contribution, Martien, HOT validator.